Amazing you gave me confidence on doing my own Thank you sir
@ewrnew3 күн бұрын
very well done
@bonifaciomagdiwang16976 күн бұрын
Easy to install but hard to remove
@mohamedelbacbir91206 күн бұрын
شكرا على الشرح
@jsonvillain8 күн бұрын
Thanks for this....
@CoolFrijolez9 күн бұрын
Looks great!
@Orangetaco2214 күн бұрын
Beautiful 3rd gen‼️😎👍🏽
@andrewhandrop178523 күн бұрын
Does it fix the lean?
@kzookid54526 күн бұрын
How hard was it to remove the head liner? I need to replace all 4 of my roof rack brackets because the white pieces are smashed down.
@theoverlanded26 күн бұрын
Oh boy. I just had to get to the back passenger corner one. I show that in the video, if I remember correctly. Good luck.
@ralphnav865427 күн бұрын
Beautiful truck! 3rd and 5th gen are said to be the best generations. I love the 3rd gen. I have 99 4WD limited w/ E locker. Bought the truck with the Caliper upgrade. It’s squeaking and a little spongy, not sure if that’s normal. Going to rebuild the calipers, or I may just have my mechanic do it. Yours is super clean. Ok thanks for the vid
@kirklane359229 күн бұрын
I like your videos! I got several ideas from this one! I am a novice at modifications and inexperienced as a mechanic so the more detail you put in the better for me! Don't hesitate to show every step in my opinion!
@raf_priv2971Ай бұрын
Can you explain why you didn't want to end the rear breathers in the gas filler area? Were there any major cons? Placing the end-breather here seems much easier.
@thomasjefferson3552Ай бұрын
how tall are you? do you hit your head on ceiling now?
@theoverlandedАй бұрын
5’7’, but the seat jackers only raise the front of the seat. Headroom remains unchanged.
@carlosk4299Ай бұрын
I want to thank you for your mess up and most importantly your fix. 😏 Good job
@wayneC7Ай бұрын
This is definitely my most favorite Nauset oversand video
@jennifertolley5454Ай бұрын
Genius!
@mikecopros79Ай бұрын
Great vid, did u purchase the steel or aluminum skids?
@_madpanda2 ай бұрын
Wish I could do this on my Prinsu. Tried the same way at first but it hits my hatch, so I ended up mouting it to the sides 😭
@southbayproducts53712 ай бұрын
Need heat to melt the lock tight
@davidnigh38002 ай бұрын
How did you get the antenna cable to stay in the windshield channel? Is there anything actually holding it in the channel, or is it mostly laying there. Great install vid though, thanks!
@theoverlanded2 ай бұрын
I just pressed it into the charnel and it has stayed put.
@grandvalleyfishslayers12792 ай бұрын
Shouldn’t you tighten up the bleeder valve before you remove the bottle?
@Explore_with_b2 ай бұрын
It really is a bitch I’m trying to get the holes and my back hurts. Currently trying as of this moment ahah
@chrisryan88632 ай бұрын
This was a great video. Great job keeping that truck in good condition!
@doberman1182 ай бұрын
didnt you just show hooking up to the starter battery ? why not just plug in the 12v socket and use while driving ? or are you adding a second battery and dc dc charger ?
@mpasaa2 ай бұрын
I kept having issues with air leaking at the hose to valve connection and zip ties didn't help so I gave up and used my backup tool....my wife LoL! Two person is so much quicker and easier in my opinion.... doesn't take that long and I don't need to deal with hose to valve connection that simply won't seal correctly....
@mirkoninhopsalot2 ай бұрын
I own the SSO roof rack. Do you know what the specs of the bolts you used to mount the awning are? I tried to match the t-bolts included but local hardware stores don't seem to know what they are
@CMS0692 ай бұрын
For anybody watching this video, stick an extension with the proper torques fitting on, heat it with a torch for a bit. That way you don’t get near your car or rack, then back it out…… This video made me cringe
@ej20542 ай бұрын
22 year ownership...awesome!
@ej20542 ай бұрын
You have great videos and your attention to detail is on point.
@joeblough46053 ай бұрын
Nice job, thanks. Do you have 2 batteries? if so, do you have a video of that install? And how long can you refrigerator run before the batteries disconnect from low voltage ?
@barryraven47453 ай бұрын
Do you have a snorkel? I was told Safari makes good ones but I haven’t done much research.
@barryraven47453 ай бұрын
Great video. I want to mount the iceco sliding tray so something like this may work to hold that down. Then you can slide out both so the lid will open unobstructed.
@jrod968194 ай бұрын
On the Labops dash mount are you able to use both USB ports?
@theoverlanded3 ай бұрын
Yes
@DFinesse884 ай бұрын
Clean!
@wrm7874 ай бұрын
The things the shop DOES NOT tell you when you get a lift kit installed. So glad I stumbled on this video! In your honest opinion, what is the worse case scenario if you do not do this install on a lifted 4Runner? I currently run the BP-51s and 285s and obviously stock panhard hah!
@ej20544 ай бұрын
Excellent! Why did you choose not to install the baseplate over the top of your canvas cover? Future setups?
@jordanfowler96984 ай бұрын
Great walkthrough. That 4Runner is cleaner than the day I picked mine up from the dealer!
@grillmastertoo4 ай бұрын
would you feel comfortable installing a metal fridge slide that also tilts down allowing easier access to inside fridge for shorter poeple?
@kenspitzler76304 ай бұрын
Where can I get that camera kit?
@theoverlanded4 ай бұрын
www.anytimebackupcamera.com/products/2020-kit
@luchforte4 ай бұрын
One suggestion, I would add a little brake fluid in the catch bottle just enough to cover the hose in the catch bottle maybe 1/4 cup to be safe so air doesn't go into the caliper. I'm sure this won't happen but figure you will have left over brake fluid so adding 1/4 cup in the can won't hurt. Thanks for the video.
@mysteriousoklahoma7774 ай бұрын
Still looks like the bar should be adjusted higher by Dr.KDSS.
@scottzreality30614 ай бұрын
Thanks for the information
@user-kn7yz4vx2c4 ай бұрын
Did anyone have problems with holes lining up?
@DavidFarley-br8iq4 ай бұрын
Hello we r very interested in going on a adventure with you..Hi I'm Hoping my husband and I can take a trip..explore the Bold Eagle state park..Hope can we get in touch..Thank you
@teddyernie4 ай бұрын
Thanks for the vid. I did this after watching this vid.
@lenaland5 ай бұрын
Can you keep the OEM TRD Pro front Skid Plate and still use the RCI for everything else...???
@mirkoninhopsalot5 ай бұрын
Thanks for the video. Got my install planned for next weekend
@shoogafree15 ай бұрын
Wonder if Midland knows they misspelled Powerful, right on the fucking box. 😂
@donalderickson-si8ww2 ай бұрын
no thay did not know and put 35 miles on the box and not tell what you need to do to get to 35 miles NO thay did not
@arzeeaj6 ай бұрын
Awesome video!! How much wire did you use?
@theoverlanded5 ай бұрын
I don’t remember exactly how much I used. The wire is pretty cheap so I’d recommend getting more than you need to minimize any additional splicing.